HG PWM 369

  • Shipping Weight: 2lbs
  • Units in Stock: 12


HG PWM 369 ( Hydrogen Garage Pulse Width Modulator,  369 Frequency) For 12/14volt DC power and up to 25 amps.  Comes with a amperage and volt digital readout on the PWM box. You can adjust the duty cycle and frequency (1hz to 150Khz) on the digital small dash display and read amps and volts on the PWM box installed by the cell. We use the 369 as an honor to Nikola Tesla. The HG PWM 3 sixty 9 is a PWM that is especially designed HHO cell controller. We use components compatible with capturing and attracting non-hertzian (-) energy. Non-hertzian energy helps produce a higher quality form of - HHO gas. True Hydroxy Gas™, ( Bob Boyce™) "We are not trying to hit resonance; we are just trying to produce a high % of the ortho spin state." “If you only knew the magnificence of the 3, 6 and 9, then you would have a key to the universe.” Nikola Tesla. We have developed a low cost PWM controller for a H2O sealed, series cell design, to run a S7 or a D7 or TD7 12v/14v DC We also have a 24v model. We use a low 96hz or 130hz 300hz or369 hz square wave pulse to the water in the cell. Frequency can be adjusted from 1 hz to 5K hz Duty cycle from 1% to 99%.

The dash displays Duty Cycle % and Frequency. It does offer constant current features with duty cycle only control.  We wanted to come up with a cheaper PWM, more affordable. We may 86 the PWM30 , 70 and 100 (8/2019) and only produce the 369 PWM’s

HG PWM 369 with Digital Dash Display. This Pulse Width Modulator/HHO Controller can handle up to 20 amps continuously. It can handle up to 50 amp negative voltage spikes. It is specially made for HHO applications, to make more of the % of Ortho HHO, the negative charged form of HHO gas that bonds to carbon +. Also designed to handle the capturing of longitudinal energy as well as the EM from your battery/alternator. These PWM's that Hydrogen Garage makes, will help produce the 4x's more powerful ortho hydrogen and oxygen. Add a set of RF choke and Inductor. We add a External fan to the PWM369 dual mosfet model. 12v or 24v input.

We can guarantee you a good % of "Ortho" hydrogen from our low voltage cell designs. The main purpose of the PWM in electrolysis is too make this magnetic hydrogen & oxygen, not(  + & -) common para hydrogen. 100% ortho hydrogen is 4x''s to 10x's  more powerful than 100% para hydrogen! Our Hydroxy Gas™ is like adding 120 octane equivlent of extra HP! Cleans out all the carbon out of your cylinders heads, rings. Also with this PWM, you can set the amp draw and it will stay close to what you set it, no matter the electrolyte concentration All brute force electrolyzers will warm up, even the most efficient ones. At the end of a day current can be easily three times as much as what you started with at the beginning of the day. Without a PWM the problem becomes finding the correct electrolyte concentration for an entire day of driving. If you start out weak then production is very slow to start out with and you lose the benefits until much later in the day. If you start out strong enough to see benefits right away, by the end of the day you're blowing fuses or greatly stressing your alternator. With a current limited PWM you set your electrolyte for the target operating current at the beginning of the day. To start the output duty cycle is 50%. Half way through the day as the cell is getting warm it may want to draw twice as much current from straight DC. ( All our PWM's are repairable, we can help you fix the PWM if ever needed. All parts are replaceable. We stock them here.)

It also hooks up with a Volo VP16 Touch Screen Controller/ECM reader.


Add a RF choke+ ( anti-toroid) and Inductor - toroid and gain 10 to 20 negative spike/volts to your HHO cell! Produces no more amps, no more volts on your meter, just makes more gas output!! and a higher quality form of HHO gas, all from water.

Add to Cart:

This product was added to our catalog on Sunday 25 August, 2019.

Copyright © 2021 Hydrogen Garage. Powered by Zen Cart
warobbo template